//=============================================================================

          	      INOGENI 4KXUSB3 CAPTURE DEVICE 

//=============================================================================

//=============================================================================
	Release Notes Version 1.89 - January 22, 2025
//=============================================================================
- Correcting issue when switching between multiple video resolutions, which 
may lead to break video streaming.

//=============================================================================
	Release Notes Version 1.87 - November 11, 2024
//=============================================================================
- Corrected minor issue with some Linux systems.
- Removed 1680x1050 support over USB2.

//=============================================================================
	Release Notes Version 1.86 - July 19, 2024
//=============================================================================
- Corrected issue where there was no audio over analog interface with some
  specific HDMI source.
- Corrected minor issues inside video processor firmware.

//=============================================================================
	Release Notes Version 1.85 - July 4, 2024
//=============================================================================
- Corrected green screen issue with macOS system.
- Correct PTZ commands that can be sent twice. Avoid sending a zoom command 
  on pan/tilt commands.

//=============================================================================
	Release Notes Version 1.83 - January 25, 2024
//=============================================================================
- Remove 640x360 resolution to correct a Logitech Roommate issue.

//=============================================================================
	Release Notes Version 1.82 - January 24, 2024
//=============================================================================
- Improve support to ZoomRoom 5.17.1. 

//=============================================================================
	Release Notes Version 1.80 - December 19, 2023
//=============================================================================
- Solved the "Enable HDMI output using self-powered hub" setting which is not
  applied correcty under macOS.
- Solved position recall on Crestron Hawk camera.

//=============================================================================
	Release Notes Version 1.78 - December 6, 2023
//=============================================================================
- Solve Zoom HID interface issue with macOS system.

//=============================================================================
	Release Notes Version 1.77 - October 6, 2023
//=============================================================================
- Corrected issue where HD-EDID is sent over source when only the power supply
  is connected. This applies only when the option "Enable HDMI output using 
  self-powered hub" is active.
  
//=============================================================================
	Release Notes Version 1.76 - September 29, 2023
//=============================================================================
- Corrected minor issue with Barco ClickShare environment.
- Loading video processor only when it is needed.
- Correcting video input display issue over USB2.0.
- Increase USB2.0 programming time.
- Solved the "Enable HDMI output using self-powered hub" setting which is not
  applied correcty.

//=============================================================================
	Release Notes Version 1.70 - Sept 22, 2023
//=============================================================================
- Corrected minor issue with Barco ClickShare environment.
- Audio quality improvement for MS Teams.

//=============================================================================
	Release Notes Version 1.68 - September 12, 2023
//=============================================================================
- Corrected speaker focus configuration under macOS for the Hawk camera.
- Added PTZ functionalities for the Hawk camera.

//=============================================================================
	Release Notes Version 1.63 - July 21, 2023
//=============================================================================
- Fix issue with Logitech Roommate over usb2

//=============================================================================
	Release Notes Version 1.62 - July 11, 2023
//=============================================================================
- Adding extension unit descriptor field for Zoom Room support.

//=============================================================================
	Release Notes Version 1.61 - June 22, 2023
//=============================================================================
- Add usb format 640x360.

//=============================================================================
	Release Notes Version 1.58 - June 7, 2023
//=============================================================================
- Fix minor issue with Crestron Hawk speaker focus camera.

//=============================================================================
	Release Notes Version 1.57 - June 1, 2023
//=============================================================================
- Fix issue when disabling audio. 

//=============================================================================
	Release Notes Version 1.54 - May 01, 2023
//=============================================================================
- Minor fix for production
- Need ControlApp version 3.12.51 to work properly.

//=============================================================================
	Release Notes Version 1.53 - April 19, 2023
//=============================================================================
- Add feature to support Crestron
- Fix offset using crestron and preset
- Need ControlApp version 3.12.51 to work properly.

//=============================================================================
	Release Notes Version 1.52 - April 17, 2023
//=============================================================================
- Add new HID interface for zoom room.
- Need ControlApp version 3.12.51 to work properly.

//=============================================================================
	Release Notes Version 1.50 - January 17, 2023
//=============================================================================
- Fix to change EDID according to USB2 of USB3
- Add support for new hardware revision
- Fix of blacking and green screen when changing format

//=============================================================================
	Release Notes Version 1.47 - December 7, 2022
//=============================================================================
- Correcting issue with zoom commands over VISCA.

//=============================================================================
	Release Notes Version 1.41 - September 13, 2022
//=============================================================================
- Corrected green screen flash issue with macOS.

//=============================================================================
	Release Notes Version 1.39 - August 09, 2022
//=============================================================================
- Corrected green screen flash issue in Zoom Rooms under MacOS.

//=============================================================================
	Release Notes Version 1.38 - April 14, 2022
//=============================================================================
- Corrected minor issue for calling presets in Zoom Rooms.

//=============================================================================
	Release Notes Version 1.37 - March 8, 2022
//=============================================================================
- Adding get/set presets using Zoom Room.

//=============================================================================
	Release Notes Version 1.35 - February 23, 2022
//=============================================================================
- Adding reset command.

//=============================================================================
	Release Notes Version 1.33 - February 23, 2022
//=============================================================================
- Corrected issue with audio output.

//=============================================================================
	Release Notes Version 1.31 - January 25, 2022
//=============================================================================
- Corrected issue where device sends black video when switching to another USB
connection.

//=============================================================================
	Release Notes Version 1.30 - January 4, 2022
//=============================================================================
- When "Force HD" mode is enabled, the device will output YUY2 only over USB.

//=============================================================================
	Release Notes Version 1.29 - December 21, 2021
//=============================================================================
- Corrected issue with Barco devices where it would not capture video.

//=============================================================================
	Release Notes Version 1.28 - December 16, 2021
//=============================================================================
- Adding support for new device enclosure.

//=============================================================================
	Release Notes Version 1.25 - May 21, 2021
//=============================================================================
- Correcting minor issue with led flashing when using self-powered hub setting.

//=============================================================================
	Release Notes Version 1.24 - May 19, 2021
//=============================================================================
- Adding configuration option in order to power up HDMI output in case the 
device is connected to a power USB hub.

//=============================================================================
	Release Notes Version 1.23 - January 29, 2021
//=============================================================================
- Custom firmware. Device is initialized as soon as it receives power.

//=============================================================================
	Release Notes Version 1.22 - January 29, 2021
//=============================================================================
- Solved issue when device is connected to powered hub and then reconnected
on the same USB bus.

//=============================================================================
	Release Notes Version 1.21 - January 20, 2021
//=============================================================================
- Allow to remove video formats by setting
- Allow to disable USB audio input through our Control App.

//=============================================================================
	Release Notes Version 1.20 - January 7, 2021
//=============================================================================
- Allow to remove video formats by setting
- Allow to disable USB audio output like v1.19 did but by setting
- Solved issue with PTZ control.

//=============================================================================
	Release Notes Version 1.19 - December 3, 2020
//=============================================================================
- No audio output available through USB (USB speaker) using this firmware.

//=============================================================================
	Release Notes Version 1.18 - November 10, 2020
//=============================================================================
- Corrected audio input issue.

//=============================================================================
	Release Notes Version 1.16 - October 28, 2020
//=============================================================================
- Preliminary version for customer.
- Adding MJPEG support over USB 2.0. 

//=============================================================================
	Release Notes Version 1.13 - September 2, 2020
//=============================================================================
- Corecting initialization bug when switching between USB hosts.

//=============================================================================
	Release Notes Version 1.12 - August 14, 2020
//=============================================================================
- Corrected audio issue under macOS.
- Corrected issue with USB connects / disconnects when device is directly
plugged to a USB hub.

//=============================================================================
	Release Notes Version 1.11 - July 8, 2020
//=============================================================================
- Corrected issue with audio when computer reboots.

//=============================================================================
	Release Notes Version 1.10 - July 2, 2020
//=============================================================================
- Adding modifications to firmware for production.

//=============================================================================
	Release Notes Version 1.9 - July 1, 2020
//=============================================================================
- Adding modifications to firmware for production.
- Almost the same thing as firmware v1.7.

//=============================================================================
	Release Notes Version 1.7 - January 28, 2020
//=============================================================================
- Corrected problem with device with specific computer hardware where device
does not get initialized properly after computer reboot.

//=============================================================================
	Release Notes Version 1.6 - January 24, 2020
//=============================================================================
- Corrected problem with PTZ control.

//=============================================================================
	Release Notes Version 1.5 - January 22, 2020
//=============================================================================
- Corrected problem with PTZ control.
- Adding customer feature.

//=============================================================================
	Release Notes Version 1.4 - October 8, 2019
//=============================================================================
- Corrected problem with PTZ control.

//=============================================================================
	Release Notes Version 1.3 - August 30, 2019
//=============================================================================
- Adding support for gain control of HDMI to codec.
- Corrected minor bugs.

//=============================================================================
	Release Notes Version 1.2 - July 19, 2019
//=============================================================================
- Corrected issue with analog audio output.

//=============================================================================
	Release Notes Version 1.1 - July 16, 2019
//=============================================================================
- Solved minor bug in video input format report.

//=============================================================================
	Release Notes Version 1.0 - June 21, 2019
//=============================================================================
- First Release.