We designed an application in order to control SHARE2/2U or CAM series devices using the USB or LAN interface. You can get the INOGENI Control App in the Support – Software tools section of this website.

Yes, these modules are available under the Support – Software tools section of our website.

Yes, the SHARE2 and all INOGENI converters are compatible with this software.

Using StarLeaf, you will need to have access to the switches below the device. Set SW1 to the ON position, power-cycle the unit and close / reopen StarLeaf software in order for changes to take effect.

Yes. All of our devices are supported by the ClickShare. ClickShare will capture video from our devices at 720p@30fps using MJPEG compression. Here are some details you might be interested.

For SHARE2 and SHARE2U:

– You can plug the devices to any USB ports on the ClickShare device.
– The SHARE2 and SHARE2U can be used as an Audio Bridge to join microphone/speaker.

For CAM300:

– You can plug the devices to any USB ports on the ClickShare device.
– You cannot use the CAM300 as a speakerphone. Only video capture is available.

For 4KXUSB3 & 4KX-PLUS:

– You must plug the device to the USB-C port on the ClickShare device.
– You can use the 4KXUSB3 as an Audio Bridge to join the microphone/speaker.

For 4K2USB3, HD2USB3 and SDI2USB3:

– You must plug the device to the USB-C port on the ClickShare device.
– You cannot use the devices as a speakerphone. Only video capture is available.

Yes. All of our devices are supported by the Kramer Connect2. Our devices can be used as a CAM300 inside Zoom and Teams apps.

*Slight detail for SHARE2U, SHARE2 and CAM300300, in order to use with Teams, make sure DIPSW#1 is ON to enable 720p video capture.

Below the device, there are switches. You need to turn on SW1 and power cycle the unit in order to make it work with GoToMeeting.

This switch allows you to support multiple video formats over USB like 720p and 1080p. When this switch is off, 1080p is the only format supported and GoToMeeting/Webex/StarLeaf does not seem to support 1080p. GoToMeeting/Webex/StarLeaf* supports 720p. The SW1 in OFF position is the default mode. We did that in order to have maximum quality over video conferencing softwares.

* Using StarLeaf, you will need to have access to the switches below the device. Set SW1 to the ON position, power-cycle the unit and close / reopen StarLeaf software in order for changes to take effect.

See below for audio routing

On the SHARE2/SHARE2U, since there is no AEC, the USB audio device is not detected as a speakerphone device, but as a digital audio input and speaker. This way the AEC of the soft codec, like Zoom or Teams will be enabled. An external DSP with AEC can also be used.

ClickShare will automatically connect to the USB speakerphone as soon as it detects it. This will then remove audio from the HDMI output. This problem can be solved by disabling the USB audio interfaces on the INOGENI device.

All you have to do is uncheck “Host USB audio” box in our app under the “Audio” tab.

By setting SW3 to the ON position below the device, you can set the device frame buffer frequency to 50Hz. This switch will also set the USB input capture to a valid frame rate in order to avoid any artifacts.

We designed an application in order to control SHARE2/2U or CAM series devices using the USB or LAN interface. You can get the INOGENI Control App in the Support – Software tools section of this website.

Yes, these modules are available under the Support – Software tools section of our website.

Yes, you can get a look at the following page for the list of known working USB 2.0 cameras.

Compatible cameras

By setting SW3 to the ON position below the device, you can set the device frame buffer frequency to 50Hz. This switch will also set the USB input capture to a valid frame rate in order to avoid any artifacts.

We designed an application in order to control SHARE2/2U or CAM series devices using the USB or LAN interface. You can get the INOGENI Control App in the Support – Software tools section of this website.

We support VGA, component and composite video on each of our analog capture devices.

If your device has a VGA input, you must use a VGA to component adapter in order to capture your component source. If your device has a DVI input, you must use a DVI to component adapter in order to capture your component source. You can capture composite video if you use the green connection of the same adapter.

Note that the DVIUSB product does not support analog video.

Yes, these modules are available under the Support – Software tools section of our website.

Yes, you can get a look at the following page for the list of known working USB 2.0 cameras.

Compatible cameras